Showing posts with label HDPE filament. Show all posts
Showing posts with label HDPE filament. Show all posts

Tuesday 23 October 2007

Stretching a point

In his article: x-idler-bracket-continued Vik Olliver alluded to the fact that you can extrude filament with a smaller diameter than the hole in the nozzle. I did some experiments to see how fine I could go. In fact the final filament diameter is simply determined by the feed rate of the extruder and the travel rate of the nozzle, or in my case the bed. The filament stretches to the length that matches the rate of travel while it is still liquid. You can then calculate the mean diameter from the volume of material extruded. The nozzle height has to be a bit less than that mean diameter and then the width becomes a bit wider.

Here are three 20 x 20 x 20 open cubes with different wall thicknesses :-



The first was 1mm diameter filament extruded at 4mm per second with a height of 0.8mm giving a wall thickness of about 1.2mm.

The second was the same feed rate but with the extruder traveling over the bed at 16mm per second to give 0.5mm filament, the same as the nozzle hole diameter. The height was set to 0.4mm giving a wall thickness of about 0.6mm. As you can see it warps more but I expect it would behave if it was building a solid object. The bottom layer which was stuck to the table has better corner definition.

The third attempt was 0.35mm filament extruded at 16mm per second with a hight of 0.28mm and a width of about 0.5mm. As you can see holes started appearing but I think that was just because the sides buckled so badly. Interestingly the holes can be bridged by filament above that needs no support. Again, I think this would be OK making solid objects, or at least objects with thicker walls.

This is really good news as it means I can get down to the sort of resolution commercial machines get (0.25mm) without having to have a very small nozzle aperture, which would limit the flow rate. It remains to be seen what effect stretching has on the polymer but as it is still liquid at that point I think it wont increase the contraction much, if at all. It does mean I need very fast head movement to keep up the deposition rate, about 64mm per second. I think my machine will do that if I reconfigure the steppers for speed rather than torque, a simple one wire change.

Friday 17 August 2007

All wound up

My years of hoarding junk is finally starting to pay dividends. I decided to address how I was going to feed the filament to my extruder. It only uses it slowly but when it runs out you have to strip down the extruder to start off a new piece. HDPE comes on a big 5 Kg reel like this :-



I thought it was asking a bit much for the extruder to rotate something that big and heavy so I started to look round for a smaller reel. I came up with this :-



It is a reel of 10000 4.7V zener diodes which I rescued from a skip. I removed the diodes, if anybody wants an envelope full just ask. It is about 270mm diameter, 70mm wide with an internal diameter of 70mm and a 30mm hole for a spindle. I wound some HDPE on to it and found that despite it being a lot smaller and lighter than the original reel it holds almost exactly half the plastic, i.e. 2.5Kg. The only problem I might have is that the plastic is quite tightly curled on the inside. Hopefully the extruder will have enough pull to straighten it.

So a plan was forming, I just needed an axle with descent bearings. Another piece of junk I had rescued from a skip was this aluminium roller:-



It was exactly the right diameter and was mounted inside a metal housing with ball bearings. I chopped up the housing to make two mounting brackets and moved the bearings around.



All that was left to do was screw it to the top of my machine. The roller is a bit long for an axle but it was easier to leave it full length than cut it and turn the end back down to fit the bearing. My lathe is nowhere near big enough for that. Here it is mounted up :-



I even managed to re-use the rubber 'O' rings on the roller to hold the reel in place. The bearings are so good that a quick twist will leave it spinning for more than 30 seconds so the extruder has no problem dragging the filament off.

Finally I replaced the knobs that I made with proper wing nuts as they are easier on the fingers.



The next task is to design the electronics to drive the extruder.